The 2016 NYC Energy Conservation Code (NYC Energy Code) regulates energy consumption in all New York City buildings, and it must be considered before designing and building any project, as well as for any modifications to existing buildings. The code establishes different requirements for commercial and residential buildings; in the case of mixed occupancies, residential and commercial are treated separately and assessed based on different chapters of the code. Although there is also a statewide code, the NYC Energy Code encompasses all its provisions while establishing additional requirements. Therefore, the statewide code cannot be used in place of the NYC Energy Code – additional requirements are not covered. A new version of the NYC Energy Code was recently published, and it applies from October 3, 2016 onwards. This version incorporates elements from the 2015 International Energy Conservation Code, as well as the ASHRAE 90.1-2013 standard.
The residential section of the NYC Energy Code establishes the general conditions that must be considered for any energy modeling or design procedure:
The code also sets requirements for materials, systems and equipment, all of which must be properly identified and labeled so that compliance can be assessed. Chapter R4 establishes the energy efficiency requirements for residential buildings, providing three approaches for compliance.
Option #1- Complying with Sections R401 through R404
This is the conventional code-based approach, and each of the sections establishes requirements for different building elements:
It is important to note that some requirements are labeled as Mandatory and others are Prescriptive. However, to comply with the energy code through this approach, all requirements must be met regardless.
Option #2 – Section R405 Plus Only Mandatory Requirements for R401 through R404
Section R405 allows the building to comply with energy efficiency requirements through a simulated energy performance analysis. If this approach is followed, it is only necessary to meet the requirements labeled as Mandatory in sections R401 through R404.
The energy performance simulation must consider space heating, cooling and service water heating. For the project to comply, its energy consumption as calculated through simulation must be less than or equal to that of a baseline design. The NYC Energy Code sets forth the minimum software requirements for this approach to be valid.
Option #3 – Energy Rating Index (ERI) as Detailed in Section R406
As with the second option, with this one it is necessary to meet all Mandatory requirements in Sections R401 through R404. Then, code compliance is achieved through an Energy Rating Index (ERI) analysis.
The Energy Rating Index (ERI) is a linear scale that goes from 0 to 100, where 0 means the building consumes zero net energy (top performance) and 100 indicates the same performance as the ERI reference design. In Climate Zone 4A, which is the case of New York City, the maximum value accepted for code compliance is 54. Of course, the result must be verified by an approved third party, and there are also requirements for software and documentation, like in section R405.
Existing Buildings
Chapter R5 sets forth the requirements for projects carried out in existing buildings, and is also broken down by sections:
In some cases, requirements from Chapter R4 may also apply. However, when this is the case, it is mentioned explicitly in the corresponding section. Historic buildings are exempt from all the requirements in this chapter of the NYC Energy Code.
The general conditions for design and simulation are the same used for residential buildings: New York City is in Climate Zone 4A, the maximum design temperature for heating load is 72°F, and the minimum design temperature for cooling load is 75°F. The code also establishes labeling requirements for all materials, systems and equipment used, which are necessary to assess compliance.
Chapter C4 focuses on commercial energy efficiency, and provides three alternatives for compliance, but they differ from those used in the residential sector. The chapter also establishes the commissioning requirements in its final section C408.
Option #1 – ASHRAE Compliance
If a building in New York City meets the requirements of ASHRAE 90.1-2013, it automatically complies with the NYC Energy Code. The complete name of ASHRAE 90.1-2013 is Energy Standard for Buildings Except Low-Rise Residential Buildings.
Option #2 – Prescriptive Compliance Path
With this approach, the building must fully comply with sections C402 through C405. Section C406 also applies for commercial spaces, and Section C406.1.1 for tenant spaces.
Option #3 – Performance Compliance Path
This option is also based on ASHRAE 90.1-2013, where the building must demonstrate compliance as required by Section 11 or Appendix G of the ASHRAE standard.
Existing Commercial Buildings
Chapter C5 establishes energy performance requirements for modifications to existing buildings, broken down by type of modification:
Just like in residential constructions, an exception is made for historic buildings.
Many of the compliance options in the NYC Energy Code require an energy analysis, and the software package must be approved. The accepted software is the following:
Before the NYC Department of Buildings can sign off the project, the following documents must be submitted:
Compliance with the NYC Energy Code can seem like a complex task at first. Although it is mandatory for project sign-off, it also offers a long-term benefit: a drastic reduction of building ownership costs in the long term. Also, since energy costs tend to rise with inflation, building owners can expect their energy savings to increase year by year, and this applies for residential and commercial constructions alike.